1220R Changelog

Release Date July 027, 2009

Problems Resolved

• In Router mode, remove LAN DNS server.
• In Client Router/Router mode, Web Server Access on WAN,Ping Access on WAN,can't setting
• When ADSL don't response to AP ,WAN PPPOE setting would change to static IP
• multi-session use MAC to record
• Add game console item
• URL filtering need at least 3 characters
• Modify MAC filtering once it's enabled could't be disabled anymore
• When the WLAN runs Static IP, the dnrd daemon will not be launched. That is, not PC can access Internet through DUT
• Set the LAN IP as 192.168.1.1 and the DHCP pool from 192.168.1.1 to 192.168.1.254. DUT will assign 192.168.1.1 to a DHCP client
• In CB mode,remove universal repeater mode.

Release Date July 03, 2009

Problems Resolved

• In CR mode, the DNS Relay doesn’t work.  DHCP client can get the DNS Server IP address directly from DUT DNS server.   
• In CB mode, the Default Gateway is useless.  DUT won’t forward its packets to default gateway while this action is necessary.
• In CB mode, when the DUT did connect an AP, UI shows correct channel in “Management -> Status” webpage.  But UI also shows a wrong channel in “Wireless -> Basic Settings” webpage.
• In CB mode, it’s impossible for DUT to send out Beacon packets. So please remove the “Beacon Interval” item in UI of CB mode.
• In CR mode, “Status” webpage shows the tile as “Bridge Router”, not “Client Router” as “Operation Mode” webpage.
• In Router mode, “Status” webpage shows the tile as “Access Point Gateway”, not “Router” as “Operation Mode” webpage.
• Please add a 30 sec countdown timer in UI .If users make previous configuration before the process finished, the httpd might  be crashed. 
• In Router mode, STP is default enabled. Please change it to default disabled.
• UI issue: In "TCP/IP->WLAN Settings->PPPoE" page, if user enter over range (1360~1399) then UI isn't pop up a wanring message.
• Static IP: DUT allow setting the same subnet IP.
• In "TCP/IP->WLAN Interface" page, please add PPPoE description.
• DUT allow multiple users to access UI.
• STP: Per IEEE802.1D, please default value change to 15.
• In AP mode, once the Universal Repeater SSID in entered and enabled, it couldn’t be cleared anymore. Disable the Universal Repeater and clear the SSID then apply still can’t clear it.
• Change operation mode or LAN IP would auto redirect to correct IP.
• The login algorithm is useless, no matter the first login or timeout login. Users can just cancel the login and do any configuration directly.

Release Date June 03, 2009

Problems Resolved

• kernel update to 1.4d

Release Date May 22, 2009

Problems Resolved

• modify opmode character "Bridge" to" Client Bridge", "Bridge Router" to "Client Router"
• remove dhcp client 、dhcp server、dhcp range in client bridge mode
• firmware upgrade can keep current setting

Release Date May 15, 2009

Problems Resolved

• modify ip_conntrack_max to 2048
• modify ip_conntrack_tcp_timeout_established to 420
• modify root file system location

Release Date May 12, 2009

Problems Resolved

• remove SNMP
• Add mutual exclusion selection of Universal Repeater Mode and WDS
• Wantcpip.asp Add MAC clone button
• Add check MTU size setting function on the WAN interface setting.
• Remove auto item in the channel selection menu when WDS or Universal Repeater Mode is enabled
• Disable DHCP server in LAN when Universal Repeater Mode is enabled.
• When flash current setting error , we use current setting backup to recover it
• Fix the wrong mode display in the status page.
• Fix the problem of changing WAN connection setting from DHCP to static IP can’t save the static DNS server problem.
• 1221 EXT (Flash-2M SDRAM-16M) can upgrade to 1221R from web

1220 PRO Changelog

Release Date July 17, 2008

New Features

• N/A

Problems Resolved

• The PPTP will be changed to PPPOE after rebooted or applying the settings.(20070321_01#9)
• In line#796 of wlbasic.asp under adhoc mode, the "disabled" is null object.(20070321_02#25)
• The SNMP_Trap will be automatically disabled in router mode after device reboot.(20070321_03#22)
• The wlan driver will be reset when connected in CB/CR_WPA2_mixed mode.(20070321_03#24)
• The UR_TBG has no proper function.(UR XOR TBG)(20070321_04#24)
• The UPNP_model URL should be "http://www.senao.com".(20070321_05#13)
• The WAN_Stats will be removed after using the refresh.(20070321_05#15)
• The stats of WLAN repeater will be missing after using the refresh.(20070321_05#19)
• The NTP server 203.60 has no proper function.(remove)(20070321_05#23)
• The stats of WLAN repeater is missing in CB mode.(20070321_05#24)
• The LLD name should be "ECB-1220R" in AP/CB/CR mode.(20070514_01#2)
• In password.asp, the "Access Point" should be "Access Point Gateway" in router mode.(20070514_01#3)
• In password.asp, the "Access Point" should be "Client Bridge" in CB mode.(20070514_01#4)
• In password.asp, the "Access Point" should be "Bridge Router" in CR mode.(20070514_01#5)
• The upnp will be automatically disabled in CR mode after device reboot.(20070514_01#6)
• The igd will be automatically disabled in CB/CR mode after device reboot.(20070514_01#7)
• The UR control will be always enabled in CR mode after device reboot.(20070514_01#8)
• The WLAN_PPPOE will be automatically disabled in AP/CB mode after device reboot.(20070514_01#10)
• The WLAN_DHCP will be automatically disabled in AP/CB mode after device reboot.(20070514_01#11)
• The WAN_PPTP will be automatically disabled in AP/CB/CR mode after device reboot.(20070514_01#15)
• The STP will be disabled from CB/CR to AP mode.(20070514_01#16)
• The NTP server 208.184 has no proper function.(remove)(20070514_01#17)
• The NTP server 129.132 has no proper function.(remove)(20070514_01#18)
• In line#74 of wlbasic.asp, the element is null object when enabling UR under AP mode(20070514_01#19)
• The stats of WLAN repeater is missing in AP mode.(20070514_01#21)
• The PPTP/L2TP/IPsec pass-through will be disabled when changing from WLAN_PPPOE.(20070517_01#1)
• When changing from WLAN_DHCP/Static IP,The PPTP/L2TP/IPsec pass-through will be disabled.(20070517_01#2)
• The WLAN_DHCP will be changed to WAN_DHCP when connected.(20070517_01#3)
• The WLAN_PPPOE will be changed to WAN_PPPOE when connected.(20070517_01#4)
• The CR/CB DHCP client will use an invalid mask when connected.(20070517_01#5)
• The SNMP_AP_TxRate has no proper function.(20070517_01#15)
• The SNMP_Router op mode is not defined.(20070517_01#17)
• The SNMP device name should be "ECB-1220R".(20070517_01#18)
• The beacon has no proper function in CR mode.(20070517_01#20)
• The UR-IF will be always enabled in CR mode after device reboot.(20070517_01#21)
• The UR-auth will be always enabled in CR mode after device reboot.(20070517_01#22)
• The WPA2_mixed_pre-auth will be enabled in CB/CR mode after device reboot.(20070517_01#23)

Changed

• When flash data indiscriminate ,we use program to recover it

Release Date May 30, 2008

New Features

• N/A

Problems Resolved

• Restore the SNMP will crash when using continous-get(20070321_03#13)
• The SNMP f/w version is invalid.
• The SNMP will crash when access 31 in CB/CR mode.
• The SNMP will crash when access 49 in CB/CR mode.
• The SNMP will crash when access 50 in CB/CR mode.

Changed

• N/A

Release Date May 27, 2008

New Features

• N/A

Problems Resolved

• The SNMP will crash when using continous-get(20070321_03#13)

Changed

• N/A

Release Date May 17, 2008

New Features

• N/A

Problems Resolved

• The WAN_DHCP client should be disabled in AP/CB mode (20080321_01#2)
• Router mode change to other mode eth1 should be down
• Router mode WAN interface default should be DHCP_SERVER

Changed

• N/A

Release Date May 16, 2008

New Features

• SNMP OID has problem, plan to solve this problem before on 5/23

Problems Resolved

• The DHCP server function is missing in AP mode.(20080514_01#20)
• The WAN_DHCP/PPPOE/PPTP client should be disabled in AP/CB mode.(20080321_01#2)

Changed

• N/A

Release Date May 14, 2008

New Features

• N/A

Problems Resolved

• Router mode DHCP Server can't input value

Changed

• N/A

Release Date May 13, 2008

New Features

• N/A

Problems Resolved

• N/A

Changed

• memory allocate 8M to 16M

Release Date May 9, 2008

New Features

• N/A

Problems Resolved

• The login window of router mode should be "Wireless Access Point Gateway". (20080509_02#11)
• The MIB string should be ""EnGenius Technologies, Inc.". (20080509_02#12)
• The MIB contact info. should be "SENAO Networks, Inc.". (20080509_02#13)
• The function DHCP client is suggested to be removed in AP/RT mode as it will cause device unreachable.(20080509_03#3)
• The TBG has no proper function.(20080509_04#8)
• The WPS will be enabled when SNMP is disabled.(20080509_04#10)
• The PPPOE_connect has no proper function in bridge router mode.(20080509_04#15)
• The PPPOE_disconnect has no proper function in bridge router mode.(20080509_04#16)
• The WLAN_PPPOE manual_connect will be reset to static IP after device reboot.(20080509_04#20)

Changed

• N/A

Release Date Arp 3, 2008

New Features

• N/A

Problems Resolved

• The WAN_DHCP/PPPOE/PPTP client should be disabled in AP/CB/CR mode.(20070321_01#2)
• The Auto_dns will be disabled in AP router mode when the LAN_DHCP is enabled.(20070321_01#4)
• The PPTP will be changed to PPPOE after rebooted or applying the settings.(20070321_01#9)
• When connected with PPPOE, the MTU will try to use 1500.(20070321_01#10)
• When connected with PPPOE, the MRU will try to use 1500.(20070321_01#11)
• The banner should be "Access Point Gateway" when switching to router mode.(20070321_02#1)
• The GA mark should be placed on the front page of the web interface.(20070321_02#2)
• In line#796 of wlbasic.asp, the "disabled" is null object.(20070321_02#3)
• In line#909 of wlwpa.asp, the "wpaAuth" is null object.(20070321_02#4)
• The web cannot be displayed when enabled/disabled the SNMP.(20070321_02#5)
• The snmp.asp should be removed in router mode.(20070321_02#6)
• In line#1331 of tcpipwlan.asp, the "document.get" is null object.(20070321_02#7)
• The title of router mode should be "Access Point Gateway". (20070321_02#8)
• In syslog.asp of router mode, the dos is missing when applying the settings.(20070321_02#9)
• In line#65 of wlbasic.asp, the "elements_checked" is null object.(20070321_02#10)
• The DHCP server will be disabled when switching from CB to router mode.(20070321_03#1)
• The default gateway should be 192.168.1.2 when switching to router mode.(20070321_03#2)
• The STP is enabled after switching from AP to CB/CR.(20070321_03#6)
• The string "3220" should be changed to "1220R" in the MIB file.(20070321_03#12)
• The SNMP will be automatically disabled in router mode after device reboot.(20070321_03#20)
• The Telnet will be automatically disabled in router mode after device reboot.(20070321_03#21)
• The SNMP_Trap will be automatically disabled in router mode.(20070321_03#22)
• The WPA2_mix mode is enabled after switching from AP to CB.(20070321_04#7)
• The status.asp cannot not handle special characters.(20070321_04#9)
• The Auto_dns will be disabled in bridge router mode when the LAN has been configured.(20070321_04#12)
• The DHCP server should be disabled in AP mode.(20070321_05#1)
• The UPNP_FN should be "EnGenius 802.11g Wireless AP/Bridge/Router".(20070321_05#2)
• The manufacutuer should be "EnGenius Technologies, Inc.".(20070321_05#4)
• The model no. should be "ECB-1220R".(20070321_05#5)
• The description should be "IEEE 802.11g Wireless AP/Bridge/Router".(20070321_05#6)
• The UPNP_model name should be "EnGenius 802.11g Wireless AP/Bridge/Router".(20070321_05#13)
• The manfufacturer URL should be "http://www.senao.com".(20070321_05#14)
• The model URL should be "http://www.senao.com".(20070321_05#15)

Changed

• The MTU of PPPOE should be 1492.(20070321_01#1)
• The default SSID should be "EnGenius" to avoid disconnections from 3220 or 8610.(20070321_04#1)
• The Turbo mode should be disabled by default.(20070321_04#2)
• The MTU of WLAN_PPPOE should be 1492.(20070321_04#14)

Release Date Mar 7, 2008

New Features

• N/A

Problems Resolved

• Remove the power control function to solve the throughput question.

Changed

• N/A

Release Date Feb 12, 2008

New Features

• When Enable LAN function under TCP/IP settings AP mode, you can use NAT function, the NAT function disable you can use Bridge function.

Problems Resolved

• N/A

Changed

• Remove Power control